ATMEGA169P-16MUR【PDF 27/274 页】IC MCU AVR 16K 16MHZ IND 64QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3753

23页 24页 25页 26页 [27页]28页 29页 30页 31页

122

8018P–AVR–08/10

ATmega169P

15.9.4

Phase Correct PWM Mode

The phase correct Pulse Width Modulation or phase correct PWM mode (WGM13:0 = 1, 2, 3,

10, or 11) provides a high resolution phase correct PWM waveform generation option. The

phase correct PWM mode is, like the phase and frequency correct PWM mode, based on a dual-

slope operation. The counter counts repeatedly from BOTTOM (0x0000) to TOP and then from

TOP to BOTTOM. In non-inverting Compare Output mode, the Output Compare (OC1x) is

cleared on the compare match between TCNT1 and OCR1x while upcounting, and set on the

compare match while down counting. In inverting Output Compare mode, the operation is

inverted. The dual-slope operation has lower maximum operation frequency than single slope

operation. However, due to the symmetric feature of the dual-slope PWM modes, these modes

are preferred for motor control applications.

The PWM resolution for the phase correct PWM mode can be fixed to 8-bit, 9-bit, or 10-bit, or

defined by either ICR1 or OCR1A. The minimum resolution allowed is 2-bit (ICR1 or OCR1A set

to 0x0003), and the maximum resolution is 16-bit (ICR1 or OCR1A set to MAX). The PWM reso-

lution in bits can be calculated by using the following equation:

In phase correct PWM mode the counter is incremented until the counter value matches either

one of the fixed values 0x00FF, 0x01FF, or 0x03FF (WGM13:0 = 1, 2, or 3), the value in ICR1

(WGM13:0 = 10), or the value in OCR1A (WGM13:0 = 11). The counter has then reached the

TOP and changes the count direction. The TCNT1 value will be equal to TOP for one timer clock

cycle. The timing diagram for the phase correct PWM mode is shown on Figure 15-8. The figure

shows phase correct PWM mode when OCR1A or ICR1 is used to define TOP. The TCNT1

value is in the timing diagram shown as a histogram for illustrating the dual-slope operation. The

diagram includes non-inverted and inverted PWM outputs. The small horizontal line marks on

the TCNT1 slopes represent compare matches between OCR1x and TCNT1. The OC1x Inter-

rupt Flag will be set when a compare match occurs.

Figure 15-8. Phase Correct PWM Mode, Timing Diagram

RPCPWM

TOP 1

()

log

()

log

-----------------------------------

OCRnx/TOP Update and

OCnA Interrupt Flag Set

or ICFn Interrupt Flag Set

(Interrupt on TOP)

TOVn Interrupt Flag Set

(Interrupt on Bottom)

TCNTn

Period

OCnx

(COMnx1:0 = 2)

(COMnx1:0 = 3)

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式